Performance of unitary heat pumps: review of ASHRAE Symposium session

1. 1. System design optimization and validation for single-speed heat pump by S.K. Fischer and C.K. Rice, Oak Ridge National Laboratories.

2. 2. Analysis of on/off cycling for an air-to-air heat pump operating in the heating mode by W.A. Miller, Oak Ridge National Laboratories.

3. 3. Field measured cycling, frosting and defrosting losses for a high efficiency air source heat pump by V.D. Baxter and J.C. Moyers, Oak Ridge National Laboratories.

4. 4. Design and available energy analysis of a heating-only residential heat pump for the Western Pacific Northwest by D.E. Elger, C.M. Reistad and S. Lang, Oregon State University.

5. 5. A study of heat pump service life by Nance C. Lovvorn, Alabama Power Company and Carl C. Hiller, Electric Power Research.

大型储罐基础非平面倾斜问题的探讨

大型储罐因基础产生非平面倾斜而影响其正常使用的情况在工程中时有发生,文章通过对某油罐工程中基础沉降观测结果的分析,探讨了储罐基础产生非平面倾斜的原因。相邻储罐之间的相互影响、充水预压未达到规范要求以及地基处理措施不当是引起储罐基础非平面倾斜的主要因素。针对相邻储罐间的相互影响,根据现行《石油化工企业设计防火规范》和《石油化工企业钢储罐地基与基础设计规范》的规定,提出以下建议:储罐布置的净距除应满足防火规范规定外,有条件时也应适当考虑对基础沉降的影响,当采用复合地基时,相邻储罐间的净距不宜小于0.6 D;当占地面积成为主要矛盾,储罐间的净距只能限制在防火规范规定的最小范围时,在地基处理时就应采取有效措施,以尽可能减少相邻储罐的相互影响。     

Frequency domain solution to delay-type Nehari problem

This paper generalizes the frequency-domain results on the delay-type Nehari problem in the stable case to the unstable case. The solvability condition of the delay-type Nehari problem is formulated in terms of the nonsingularity of three matrices. The optimal value γ_opt is the maximal γ∈(0,∞) such that one of the three matrices becomes singular. All sub-optimal compensators are parameterized in a transparent structure incorporating a modified Smith predictor.     

流动注射分光光度法测定钴

研究了将ＰＡＮ用于流动注射（ＦＩＡ）分光光度法测定微量钴，在５６０ｎｍ处绘制标准曲线，线性范围为０～４５μｇ／ｍｌ，相关系数０．９９６，方法的相对标准偏差（ＲＳＤ）小于３％，加标回收率为９５％～１０５％，进样频率８０次／ｈ。本法简单快速，用于面粉、分子筛，铝合金测定结果令人满意。     

美国UCC公司项目实施八段法

国外工程公司的项目实施工作法是科技发展和经济发展的产物。公司为谋求生存和发展,必须采取先进的技术和科学管理,同时获得适当的利润回报。本文介绍美国UCC公司的项目工作八段法。     

用迁移率和载流子浓度研究碲镉汞中的深能级

获得了一种研究碲镉汞深能级的方法。通过分析迁移率 载子浓度与温度的关系，可以得到关于深能级的重要依据。     

Automatic generation of IDEF0 models

This paper looks into a new area for knowledge-based system application, that of manufacturing modelling. Manual generation of IDEF0 models of manufacturing systems is time-consuming and inconsistent. However, the process can be automated to improve timeliness and consistency. In this paper, a knowledge-based manufacturing modelling system for the automatic generation of IDEF0 models is proposed. The system will not only greatly reduce the IDEF0 modelling time but will also eliminate the inconsistency problem of conventional IDEF0 modelling systems. The paper explains the knowledge-based approach and identifies the kinds of domain knowledge that are required for the construction of the knowledge-based manufacturing modelling system.     

Catalytic behavior of YBa2Cu3O7-x in the partial oxidation of methanol to formaldehyde

The partial oxidation of methanol to formaldehyde was studied over YBa₂Cu₃O_7-x catalyst in a flow reactor. The structural change of YBa₂Cu₃O_7-x before and after the reaction was measured by means of XRD and iodometric titration method. The catalytic characteristics of YBa₂Cu₃O_7-x for the partial oxidation of methanol to formaldehyde was due to copper ions. It was found that Cu⁺² was responsible for the higher selectivity for formaldehyde.     

Si_（1－x）Ge_x／Si定向耦合器的研制

在运用ＳｉＧｅ脊形波导单模条件和有效折射率法分析ＳｉＧｅ／Ｓｉ定向耦合器结构参数的基础上，采用分子束外延和各向异性腐蚀技术制备出Ｓｉ１－ｘＧｅｘ／Ｓｉ（ｘ＝０．０５）单模定向耦合器．在波长为１．３μｍ时，平均串音小于－１８．１ｄＢ，输出功率耦合效率达到９８．１％     

Ammonia-water absorption machines for refrigeration: theoretical and real performances

In principle, absorption chillers of the ammonia-water type could work at temperatures well below the usual air-conditioning temperatures, arriving at the range 250–260 K, which can be useful for refrigeration applications. This possibility is studied for an air-cooled machine, comparing the results with the experimental data supplied by a manufacturer that recently commercialized such a refrigerator. The prediction is fair, and the study allows an insight into the internal parameters and into the possible behaviour for more severe conditions than those studied.